Hardware:
Q: Why Spooky2 Scalar Digitizer cannot be used with XM Generator?
A: Spooky2 Scalar Digitizer measures tiny changes in the scalar field during a scalar frequency scan through detecting phase angle, but XM can’t detect phase angle. So Spooky2 Scalar biofeedback can only be performed with GX.
Q: Why not have the GX within the scalar field when doing Scalar biofeedback?
A: The reason why GX should not stay in scalar field while doing biofeedback is that the scalar biofeedback is quite accurate and sensitive. Any kind of disturbance should not occur. GX will cause the scalar field to be disrupted while running from within the field in general, not just during the biofeedback. So we recommend that GX should not stay in scalar field.
Q: It is normal that the light on the Receiver does not turn on when doing scalar biofeedback scan?
A: The Receiver light may be on, dim or even off. Because some power is lost in the Digitizer, the link cable becomes more sensitive to the effects of earthing. If the led if off, you can do a test to make confirm that a scalar field is present. Go to system tab and select “Display GX current and angle”. The graph in the control tab will then display the current on the selected generator. Placing your hand in the scalar field should influence the graph, proving a scalar field is present.
Software:
Q: Is it OK when doing a biofeedback with Scalar Digitizer to do a baseline first?
A: Scalar Digitizer biofeedback scan is smooth, so baseline is not required.
Q: Why is the frequency range from 100 to 50 kHz when using Scalar Digitizer?
A: This is the optimum range for Spooky2 Scalar modulation. You can modulate up to 5 MHz if you wish, but the scalar field becomes distorted.
Q: Are scalar biofeedback scan frequencies modulated all real time? What’s the recommended duration of a scalar biofeedback scan in software?
A: Same as GX scan, after doing Scalar biofeedback scan, you should run the scan results to do some treatments. Please remember to remove Spooky2 Scalar Digitizer when you run scan results. Please check the recommended duration in Spooky2 software.
Q: What exactly do you do after running a scalar biofeedback scan?
A: After you complete a scan, you will get a list of frequencies that show up as your scan results. These can be saved in a custom program that you can run through the scalar unit. Select scalar shell preset, click on program tab and select your custom program. Click on control tab, check overwrite box, and click on your generator number to run the results on the scalar unit.
Miscellaneous:
Q: Can I perform other biofeedback scans in scalar field? Why can I do biofeedback scan using Scalar Digitizer?
A: No, you cannot perform other biofeedback scans whilst in scalar field, since they use different detecting way and the field will affect the scan results. For example, Spooky2 Pulse detects your heart beats, which would be affected by the scalar field. However, Spooky2 Scalar Digitizer measures tiny changes to the scalar field during scalar frequency scans, while GeneratorX records how the electrical signal behaves, so only Scalar Digitizer can do biofeedback scan in Scalar field.
Q: What methods do you suggest for running the Scalar biofeedback results?
A: You can run the hits using any method, such as remote or contact, though scalar would be the best, as that was how the frequencies were applied and hits found.
Q: Where can I put the DNA sample whilst doing scalar biofeedback scan?
A: Scalar Digitizer is different from Sample Digitizer, you don’t need to have your DNA on it and you just need to lie between two Scalar boxes.
Q: Can I do biofeedback scan just with saliva in scalar field to run the Spooky2 Scalar Digitizer Hunt and Kill scan?
A: No. Saliva is way too small. Other things such as dust particles will have a greater effect on the scalar field.
If I am doing a scalar biofeedback with digitizer and xm pro and receive only high numbers, such as the threshold 500-50000 and all my results at 49,999,-49,100 would this be caused by interference from an outside source, and if so, what could be done to the field to remedy this? I am in a room with windows. There is no metal in the field. Everything is hooked up correctly. Same equipment in a different space on inside walls of a block building receives more accurate results. Any idea what can be done to preserve the field for accuracy?
If I am doing a scalar biofeedback with digitizer and xm pro and receive only high numbers, such as the threshold 500-50000 and all my results at 49,999,-49,100 would this be caused by interference from an outside source, and if so, what could be done to the field to remedy this? There is no metal in the field. Everything is hooked up correctly. Same equipment in a different space on inside walls of a block building receives more accurate results. Any idea what can be done to preserve the field for accuracy?
Would you recommend running Biofeedback Hunt/Kill with Scalar every night, and sleep with it? Or how often can this be run during a week?
Hi, Dustin. Yes, you can. It’s up to you. You can run Biofeedback Hunt/Kill with Scalar every night. We recommend that you do a detox to clean out the excess waste in your body because you’re doing killing every day.
After we receive the results from the scalar biofeedback scan (BFS) it shows the frequencies and the health challenges that are related to those frequencies. Each frequency shown are also listed with one or many health challenges.
Is there a way to narrow this down to show less health challenges? Or is it just a matter of utilizing scalar to help reduce the health challenges and later do another BFS in order to see possibly less health challenges? I understand that not all health challenges are the same and there for the solutions for removing them are different.
I think I just answered my own question here but it may help others with similar question maybe.
Hi, Kevin. You can change the Max Hits to Find in the Control Tab to show fewer health challenges. If you want to improve the scalar scan results, you can add loops and reduce Initially Step Size.
Can I use pure scalar energy over night while having hormone therapy for cancer.
Many thanks
Hi, John Costin. It is safe for you to use pure scalar energy overnight while having hormone therapy for cancer.
Concerning the last question above in your list :
Do you mean we can do a scalar BFB with nail powder in the scalar field an nobody in the field ? Can you explain morde waht can be used for BFB in the scalar field ?
Thank you.
Hi, Henri Pavot. We don’t suggest putting your DNA sample on it to do a BFB, you just need to lie between two Scalar boxes.