Spooky2 Scalar Q&A

Spooky2 Scalar Frequency Imprinting Q&A

Q: For imprinting, where do I put the glass of water and the essential oils?

A: If you want to send the effects of an essential oil, supplement or drugs, etc, in your body or into something else, place the substance on the receiver coil.

If you wish to imprint information into water for drinking, place the water on the transmitter coil, and the modulated information substance on the receiver coil.

If you want to imprint frequency into water using a generator, you can place the water on the transmitter coil after you connect a Spooky2 generator to the transmitter.

Q: Will it be overdosage if the imprinting time is too low?

A: There shouldn’t be any concern about over-doing the imprinting since JW has said that with scalar fields, your body and the water/substance will take what it needs and discard any excess. So the only real concern should be if the imprinting is long enough or too short.

Q: How long does it take to print information into the water?

A: It only takes a few minutes to imprint information into a small container. A glass of water could take 10 minutes for more. A larger container would take even longer.

Q: Will the EMF be imprinted into the water?

A: The water does have the low frequency from the EMF but not much, as low frequencies take longer to imprint. The EMF is not absorbed and retained. Only the frequency of 50 or 60 Hz.

Q: Can filtered pure water helps the body retain the frequencies?

A: 1. Personally, I feel drinking lots of filtered pure water before a Scalar session can help the body retain the Frequencies sent through it, As water holds memory, your body, and all its cells can hold Scalar Memory.

2. Sometimes, I find it’s a good idea to have a glass of water on the Scalar when running pure scalar too – my system handles it better, more comfortably.

Q: I have three forms of B12 – 2 liquid and one pill. Can I imprint one of these into a glass of water and drink it? If so, what is best, liquid or pill? And what about dosage?

A: Both liquids and solids can modulate the scalar field with the same efficiency. The same molecular information is being transferred. You can use either liquids, solids, or both together. It is entirely up to you.

It should only take about 3 minutes to imprint a small glass of water. Remember to tune Spooky2 Scalar after placing the water on the transmitter coil.

Researchers generally instruct people to only take several drops of the frequency-imprinted water for each “dosage”.

During frequency imprinting, it is often advantageous to be within the scalar field, so you get the benefits of the field during the process. In this way, the water will be tailor-made for you.

There is no indication that you can overdose with this method when using scalar fields, and personally I’ve tried using an Advil pill for extended periods of time with no adverse effects.

Of course, trust your instincts and do what you feel is appropriate.

Q: How high someone can place a sample on the transmitter coil? Will the supplements piled in the container be imprinted equally?

A: Closer is better. We have not determined the absolute maximum distance. We recommend placing the sample directly on the coil, in which case the distance is small. Large vessels like jugs may have some contents further from the coil, but this has not adversely affected performance.

No. The ones closer to the coil will add more information to the scalar field.

Q: If I want to do the imprinting water, should I place the water first and then do the tuning?

A: Yes, you should retune your Spooky2 Scalar after you placing the water on the transmitter coil.

Q: Can I be in the scalar wave while imprinting frequencies into the water?

A: Yes. The water frequency will then be tailor-made for you, since it will also contain the natural frequencies of your body, and the effect the scalar wave had on it.

Q: Can you explain why it’s recommended to put water to imprint on the transmitter, while substances to transmit molecular information should be placed on the receiver?

A: The energy flows from the transmitter to the receiver, then back. There is no scalar field until it hits the receiver and then returns back to the transmitter.

Therefore, in order to add substance information to the field, the first entry point is the receiver coil. That information is then carried back to the transmitter. Once at the transmitter, the information can be imprinted to whatever is on the transmitter coil.

I did one experiment to test the properties of the transmitter coil vs. receiver coil in regards to structuring water. I’ll post a thread on this.

Thread created and can be found here:
https://www.spooky2.com/forums/viewtopic.php?f=117&t=9823

3 thoughts on “Spooky2 Scalar Frequency Imprinting Q&A

  1. Eila Algood says:

    can I imprint on crystals?

  2. Ronnie says:

    How to imprint on cloth?

    1. Dear Ronnie, if you want to imprint something, you need to put the items on the transmitter coil. But we strongly recommend you do water imprinting.

Leave a Reply

Your email address will not be published. Required fields are marked *